Tjernlund SS1C SideShot with UC1 Universal Control (Version Manual de usuario

Copyright © 2004, Tjernlund Products, Inc. All rights reserved P/N 8504103OWNER INSTRUCTIONS, DO NOT DESTROYRecognize this symbol as an indication of

NOTCH BRACINGIt is recommended and local codes may dictate that the joist be reinforced as outlined below. Bracing of the rim joist is not necessary.

10INSTALLATION OF VENT PIPE A barometric draft control must be used. Install the barometric draft control as shown, (See Diagram K). The SideShot Ve

114. Using a tube cutter, cut the sensing tube 2" from the elbow directed at the vent pipe inlet collar, (See Diagram L). Discard the cut off se

ELECTRICAL WIRING All wiring from the UC1 to the appliance must be appropriate Class 1 wiring as follows: installed in rigid metal conduit, intermedia

13SIDESHOT WITH INTEGRAL UC1 UNIVERSAL CONTROL CONNECTED TO A HONEYWELL R8184 SERIES OR EQUIVALENT PRIMARY CONTROL50/60 HzRWHITEORANGEBLACKHONEYWELLR8

14SIDESHOT WITH INTEGRAL UC1 UNIVERSAL CONTROL CONNECTED WITH AN AQUASTATXNRUNIVERSAL CONTROLLERLINE VOLTAGE OIL BURNERPRIMARY CONTROL, BURNERL1NXLJ1J

15SIDESHOT WITH INTEGRAL UC1 UNIVERSAL CONTROL CONNECTED WITH A SINGLE ZONE 24 VAC THERMOSTATXNRUNIVERSAL CONTROLLERTHERMOSTATGGINTERNAL CONTROLOF FUR

SELECTION OF PRESSURE SWITCH BLEED ORIFICEIn order for the SideShot pressure switch to function properly for the intended application, the proper blee

NOTES: All draft adjustments are approximate. Thischart is to be used for initial draft adjustment only.Subsequent draft adjustments may be required

186. Perform a smoke test and make any adjustments to the burner air shutter, SS1C draft control on the vent hood or the barometric draft control to a

1Tjernlund Products welcomes your comments and questions. Address all correspondence to:Customer Service • Tjernlund Products, Inc. • 1601 Ninth Stre

19REMINDER : The most significant preventer of wind-induced air infiltration is choosing a proper termination location of the SideShot before installa

20CHECKING MEMORY FOR LAST FAULT CODE IMPORTANT: Prior to accessing the fault code memory, note the settings of the dip switches so that they can be r

21DIAGRAM NNOTE: Insufficient post-purge may cause limit to trip. If the limit switch trips, verify that the post-purge setting is long enough toremov

22WHEEL REPLACEMENT (DIAGRAM N)1. Loosen set screw from wheel hub by using a 5/32” allen wrench.2. Twist wheel to loosen and pull off of motor shaft.

23TJERNLUND LIMITED TWO YEAR WARRANTYTjernlund Products, Inc. warrants to the original purchaser of this product that the product will be free from d

2SPECIFICATIONSMotor: 115/1/60, 3300 RPM, 212 watts, 2.28 FLAFan Proving Switch: Non-adjustable, N/O with a set point of -.04" W.C.High Limit:

The SS1C must be installed by a qualified installer (an individual properly licensed and/or trained) in accordance with all local codes or, in their a

SS1C WITH INTEGRAL UC1 UNIVERSAL CONTROL BOARD FEATURES# 1. Power supplied by board. Do not supply power to this area or control damage may result.#

LED FAULT INDICATORSFault conditions are indicated by counting the number of times LED #4 (Red) flashes.LED #4 Flashes 2 Times Fan Prover was in elect

PLENUM AND VENT PLENUM AND VENT HOOD CLEARANCE FROM COMBUSTIBLESWith an inlet flue gas temperature of 301oC (575oF) or below, the SideShot has been L

INSTALLATIONTools required:• Reciprocating Saw • 1/2", 7/16",5/8" Wrench• Drill and 1/8", 1/4", 1/2" Bits • 1/4" Ma

9. Connect the Plenum to the Vent Hood of the SideShot following the steps on pages 8, 9 and 10. 10. After the SideShot is completely installed, apply